change time NISSAN PATHFINDER 2008 R51 / 3.G 04IT Navigation Manual

Black plate (159,1)
Model "NISSAN_NAVI" EDITED: 2007/ 2/ 26
SET AVERAGE SPEEDS
You can calculate the required time to the
destination based on the set vehicle speeds.
Basic operation
1. Highlight [Set Average Speeds] and push
<ENTER>.
2. Highlight the preferred item and push
<ENTER>.
3. Use the joystick to make an adjustment. The
speed can be increased/decreased by 5
MPH (5 km/h) .
4. After finishing the setting, push<ENTER>
or<BACK>to activate the setting.
5. Push<BACK>to return to the previous
screen. Push<MAP>to return to the
current location map screen.
NAV2919
Available setting items
.Auto:
If set to ON, the system automatically
calculates the required time to the destina-
tion, the indicator illuminates and the speed
settings cannot be changed.
.Freeway:
Allows you to adjust the average vehicle
speed on a freeway by moving the joystick in
the direction of [+] or [−]..Main Road:
Allows you to adjust the average vehicle
speed on a main road by moving the joystick
in the direction of [+] or [−].
.Town Road:
Allows you to adjust the average vehicle
speed on a town road by moving the joystick
in the direction of [+] or [−].
.Residential:
Allows you to adjust the average vehicle
speed in a residential area by moving the
joystick in the direction of [+] or [−].
Route guidance5-33

Black plate (214,1)
Model "NISSAN_NAVI" EDITED: 2007/ 2/ 26
CLOCK SETTINGS
This allows you to change the clock settings.
Basic operation
1. Highlight [Clock] and push<ENTER>.
2. Highlight the preferred adjustment item.
3. Use the joystick to adjust to the preferred
setting.
4. After setting, push<ENTER>or<BACK>
to apply the setting.
5. Push<BACK>to return to the previous
screen. Push<MAP>to return to the
current location map screen.
NAV3036
Setting items
.Hour:
Set the hour.
Adjust the hour by tilting the joystick in the
direction of [+] or [−].
.Minutes:
Set the minutes.
Adjust the minutes by tilting the joystick in
the direction of [+] or [−]..Auto Adjust:
The time currently set is reset to the GPS
time.
.Daylight Saving Time:
Select to toggle the daylight saving time
setting between on and off. The indicator
light illuminates when the daylight saving
time setting is set to on.
8-10Other settings

Black plate (221,1)
Model "NISSAN_NAVI" EDITED: 2007/ 2/ 26
CLOCK SETTINGS
This allows you to change the clock settings.
Basic operation
1. Highlight [Clock] and push<ENTER>.
2. Highlight the preferred adjustment item and
push<ENTER>.
3. Use the joystick to adjust to the preferred
setting.
Push<ENTER>to set ON/OFF.
4. After setting, push<ENTER>or<BACK>
to apply the setting.
5. Push<BACK>to return to the previous
screen. Push<MAP>to return to the
current location map screen.
NAV3008
Setting items
.On-screen Clock:
Select to toggle the clock display located in
the top right corner of the display between
on and off. The indicator light illuminates
when the clock display is set to on.
.Clock Format:
Use the joystick to change the clock format
between 12-hour and 24-hour..Offset Adjust:
Use the joystick to adjust the offset value
(between−59 and +59) .
.Daylight Saving Time:
Select to toggle the daylight saving time
setting between on and off. The indicator
light illuminates when the daylight saving
time setting is set to on.
Other settings8-17

Black plate (240,1)
Model "NISSAN_NAVI" EDITED: 2007/ 2/ 26
.If waypoints are set, the system calculates
multiple routes between waypoints simulta-
neously, and the following may result.
— If one section between waypoints cannot
be calculated, none of the route will be
displayed.
— The route may not connect completely at
some waypoints.
— The route may require a U-turn close to
some waypoints.
.Route calculation may not be completed in
the following cases.
— If there is no main road within a range of
1.5 miles (2.5 km) from the vehicle, a
message saying so will appear on the
screen. Try recalculating when the vehi-
cle is closer to a main road.
— If there is no main road within a range of
1.5 miles (2.5 km) from the destination or
waypoint, a message saying so will
appear on the screen. Try setting the
location closer to a main road.
— If the vehicle is too close to the
destination or if there are no roads to
the destination, a message saying so will
appear on the screen.— If it is impossible to reach the destination
or waypoints because of traffic regula-
tions, etc.
— If the only route to reach the destination
or waypoints is extremely complicated.
— If the destination, current vehicle position
or waypoint is within the “Avoid Area”.
— If a part of the route is included in the
“Avoid Area”.
.The following may occur when the route is
displayed.
— If you calculate a route on a main road,
the starting point of the route may not
exactly match the current vehicle loca-
tion.
— The endpoint of the route may not
exactly match the destination.
— If you calculate a route on a main road,
the system may display a route from
another main road. This may be because
the position of the vehicle icon is not
accurate. In this case, park the vehicle in
a safe location and reset the vehicle
icon, or continue driving to see if the
position of the vehicle icon is automati-
cally adjusted before recalculating the
route.— There are cases in which the system
shows an indirect route to reach the
destination or waypoints, if you set them
from stored or facility information. In
order to correct this, you must be careful
about the traffic direction, especially
when lanes with different travel direc-
tions are shown separately, such as
interchanges and service areas.
— This system makes no distinction be-
tween limited traffic control and total
control (blockage) . It may show an
indirect route even if the road is usable.
— Even if the freeway preference is set to
OFF, a route that uses the freeway may
be suggested.
— Even if the preference is set to OFF, a
route that uses a ferry line may be
suggested.
— Ferry lines, excluding those that are only
for pedestrians, bicycles and motor-
cycles, are stored in this system. Take
into consideration the travel time re-
quired and operational condition before
deciding whether to use them or not.
9-10General system information